READ THOROUGHLY BEFORE INSTALLING

WARNING

Risk of electric shock

• Turn power o before servicing

– see instructions

GEH-5983

INSTRUCTIONS

UltraStar

Luminaire

T5 / T8 Fluorescent Luminaire

GENERAL

This luminaire is designed for indoor applications only and should be installed and maintained

according to the following recommendations. Check label for damp or wet location suitability.

Any part damaged or broken during or after assembly or installation should be replaced.

UNPACKING

This Luminaire has been properly packed so that no parts should havebeen damaged

during transit. Inspect to conrm. No damaged parts should be installed.

Attention: Sheet metal parts may have sharp edges that may cause injury. The

manufacturer recommends caution during installation and the use of gloves when

possible. Remove all protective lm from reectors before energizing xture.

WIRING

Make all electrical connections in accordance with the National Electrical Code and any

applicable local code requirements. Check to be sure that labeled ballast voltage matches

supply voltage. Use supply wire rated minimum 90°C.

FIXTURE INSTALLATION (VH, HB, AL, SS, ES, FH, SR, NH, VP and EH Series)

a. EZ Leveling stright-cable or EZ Leveling Y-toggle cable can be used to mount

xture.

b. Attach EZ leveling cable to each end of xture, attaching through mounting slot.

2. S-Hook Hanging

Fixtures can be installed using S-hook (not supplied) using mounting detail on top

ends of xture.

3. NH series xture has integral threaded inserts and supplied eye-bolts.

Attach EZ level cable to eye-bolts for mounting of xture.

4. VP series xtures are supplied with mounting brackets. Attach EZ level cable to

mounting brackets for mounting of xture.

5. After xture is mounted access ballast for wiring as follows:

a. SR, ES, SS, AL Series: Remove reector/ballast cover by twisting reector

fasteners quarter-turn,

b. HB, NH Series: Remove top-access ballast cover by unsnapping ballast cover.

c. FH, VH Series: Plug directly into Modular Wiring Plug at side of ballast channel.

d. VP Series: Remove reector clips.

6. Make connection to ballast leads per wiring diagram on ballast.

7. Reinstall reector/ballast cover.

8. Peel protective covering from reector (Miro nish reectors).

9. Install lamps

LAMP

WARNING

Unit will fall if not installed properly

• Follow installation instructions

WARNING

Sharp edges may be present

• Gloves should be worn during installation

Installing SR, ES, SS, AL series xtures

1. EZ Leveling cable (see EZ Leveling cable attachment instructions below).

a. Four EZ Leveling straight- cables required to hang xture.

b. Attach EZ Leveling cable to each end of xture at mounting detail.

2. After xture is mounted:

a. Remove reector by turning reector fasteners quarter-turn.

Make connection to ballast leads per wiring diagram on ballast.

c. Reinstall reector.

d. Peel protective covering from reector.

e. Install lamps.

Installing VH, HB, FH, NH, VP series xtures

1. EZ Leveling cable (see EZ Leveling cable attachment instructions below).

CAUTION

Risk of burn

• Allow lamp/xture to cool before handling

Use only lamps specied on nameplate. Observe lamp manufacturer’s recommendations

and restrictions on lamp operation, particularly ballast type, burning position, etc.

Attaching Modular Wiring Harness (optional component)

Insert supplied modular plug wiring harness into the receptacle on the end of the xture

and tie the wire to the cable hanger up to main power source.

VH Series HB Series AL Series SS Series ES Series

FH Series SR Series NH Series EH Series VP Series

Components for Installing SS Series Fixtures

Reector/ballast cover must be installed to complete enclosure! Assemble reector part

RSFSS8-844UP-W only with BP-S082/ S081 Strip xture!

BR-S4-2LE-P-SS

Install socket/

socket bracket

assembly into

slots at end of

xture. Twist end

of tab with pliers

to insure locking

as shown.

BP-S054

If xture is run

across red iron,

use Bracket

Connector Kit for

alignment and

stiening.

BP-S009 or

BP-S067

If xture is run

with red iron,

use either a

slide-in connector

for alignment

proposes.

BP-S068

If xture is at the

end of a row, use

Tall End Plate

to cover end of

xture.

HW-F041

Attach alignment

clips to join

next reector if

required.

Lighting Solutions

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation or

maintenance. Should further information be desired or should particular problems arise which are not covered suciently for the purchaser’s purposes, the matter should be referred to

GE Lighting Solutions.

1 2 3 4

Sommario

Pagina 1 - T5 / T8 Fluorescent Luminaire

READ THOROUGHLY BEFORE INSTALLINGWARNINGRisk of electric shock• Turn power o before servicing – see instructionsGEH-5983INSTRUCTIONSUltraStar® L

Pagina 2

MAINTENANCEIt will occasionally be necessary to clean the outside of the refractor to maintain the light level. Frequency of cleaning will depend on t

Pagina 3 - ATTENTION

LIRE ATTENTIVEMENT AVANT D’INSTALLERAVERTISSEMENTRisque d’électrocution• Couper l’alimentation électrique avant toute réparation – Voir les ins

Pagina 4 - AVERTISSEMENT

(Type 1)(Type 2)35-201578-175 (1/10)ENTRETIENIl sera périodiquement nécessaire de nettoyer l’extérieur du réfracteur pour préserver la qualit

Commenti su questo manuale

Nessun commento

Case Logic VNA210K + MOUSE manuály

Uživatelské manuály a uživatelské příručky pro Pouzdra na notebook Case Logic VNA210K + MOUSE.
Poskytujeme 1 manuály pdf Case Logic VNA210K + MOUSE ke stažení zdarma podle typů dokumentů: Datový list

Case logic VNA210K + MOUSE Datový list (1 strany)

Značka: Case-logic | Kategorie: Notebook cases | Velikost: 0.09 MB |

Tabulka s obsahem

VNA-210K + Mouse

Další produkty a příručky pro Pouzdra na notebook Case Logic

Modely	Typ Dokumentu
TNC-216	Datový list Case Logic TNC-216, 1 stránky
ULB116G	Datový list Case Logic ULB-116 Backpack 16" grey, 1 stránky
FSI	Datový list Case Logic Professional Notebook Case 18", 68 stránky
VNA216K + MOUSE	Datový list Case Logic VNA-216K + Mouse, 1 stránky
ULA112P	Datový list Case Logic ULA-112, 1 stránky
ULA116G	Datový list Case Logic ULA-116, 1 stránky
ZLCS114	Datový list Case Logic ZLCS-114, 1 stránky
ENC117	Datový list Case Logic ENC-117, 1 stránky
ULA110P	Datový list Case Logic ULA-110P Netbookcase 10" purple, 1 stránky
PNM217K	Datový list Case Logic PNM-217, 1 stránky
PLS212K	Datový list Case Logic PLS-212, 1 stránky
PNC114	Datový list Case Logic PNC-114, 1 stránky
PBCI116M	Datový list Case Logic PBCI-116M, 1 stránky
PBCI112M	Datový list Case Logic PBCI-112, 1 stránky
VNC218	Datový list Case Logic VNC218, 1 stránky
PLS210B	Datový list Case Logic PLS-210, 1 stránky
PNM214	Datový list Case Logic PNM-214, 1 stránky
PLS214B	Datový list Case Logic PLS-214, 1 stránky
TNC218	Datový list Case Logic TNC-218, 1 stránky
PBCI114R	Datový list Case Logic PBCi-114, 1 stránky

GE AL5 Guida di Installazione